Request a sample
Sign up to our Monthly Newsletter...
Got a question
or an enquiry?
Click here and our friendly staff
will be happy to assist you.
will be happy to assist you.
Click here for a PDF
version of this page.
version of this page.
All information is given for guidance only
and designers should satisfy themselves as to
the suitability of the specification
by requesting samples
and designers should satisfy themselves as to
the suitability of the specification
by requesting samples
Screwin* Insert Short for Thermoplastic
Click Here for larger image
Series 20105 Type : TC
Screwin* Insert Short for Thermoplastic
Screwin* Insert Short for Thermoplastic
| Part No. | Thread M | Insert Length H | Ext. diam. A | Pitch P | Hole Diam d | Wall min E | Boss B | Hole depth minP | Style |
| Part No. | Thread M | Insert Length H | Ext. diam. A | Pitch P | Hole Diam d | Wall min E | Boss B | Hole depth minP | Style | |||
| TC020H040 | M2 | 4.00 | 3.50 | 0.79 | 3.10 | 1.20 | 5.50 | 4.40 | SHORT |  | ||
| TC020H048 | M2 | 4.80 | 3.50 | 0.79 | 3.10 | 1.20 | 5.50 | 5.30 | STANDARD | | ||
| TC020H053 | M2 | 5.25 | 3.50 | 0.79 | 3.10 | 1.20 | 5.50 | 5.80 | LONG | | ||
| TC025H040 | M2.5 | 4.00 | 4.33 | 1.06 | 3.80 | 1.45 | 6.70 | 4.40 | SHORT | | ||
| TC025H053 | M2.5 | 5.25 | 4.33 | 1.06 | 3.80 | 1.45 | 6.70 | 5.80 | STANDARD | | ||
| TC025H063 | M2.5 | 6.25 | 4.33 | 1.06 | 3.80 | 1.45 | 6.70 | 6.90 | LONG | | ||
| TC030H040 | M3 | 4.00 | 4.73 | 1.06 | 4.10 | 1.55 | 7.20 | 4.40 | SHORT | | ||
| TC030H053 | M3 | 5.25 | 4.73 | 1.06 | 4.10 | 1.55 | 7.20 | 5.80 | STANDARD | | ||
| TC030H063 | M3 | 6.25 | 4.73 | 1.06 | 4.10 | 1.55 | 7.20 | 6.90 | LONG | | ||
| TC035H050 | M3.5 | 5.00 | 5.52 | 1.16 | 5.00 | 1.90 | 8.80 | 5.50 | SHORT | | ||
| TC035H062 | M3.5 | 6.20 | 5.52 | 1.16 | 5.00 | 1.90 | 8.80 | 6.90 | STANDARD | | ||
| TC035H073 | M3.5 | 7.30 | 5.52 | 1.16 | 5.00 | 1.90 | 8.80 | 8.10 | LONG | | ||
| TC040H056 | M4 | 5.60 | 6.31 | 1.26 | 5.80 | 2.20 | 10.20 | 6.20 | SHORT | | ||
| TC040H071 | M4 | 7.10 | 6.31 | 1.26 | 5.80 | 2.20 | 10.20 | 7.80 | STANDARD | | ||
| TC040H084 | M4 | 8.40 | 6.31 | 1.26 | 5.80 | 2.20 | 10.20 | 9.30 | LONG | | ||
| TC050H064 | M5 | 6.40 | 7.50 | 1.40 | 6.90 | 2.60 | 12.10 | 7.10 | SHORT | | ||
| TC050H084 | M5 | 8.40 | 7.50 | 1.40 | 6.90 | 2.60 | 12.10 | 9.30 | STANDARD | | ||
| TC050H100 | M5 | 10.0 | 7.50 | 1.40 | 6.90 | 2.60 | 12.10 | 11.0 | LONG | | ||
| TC060H079 | M6 | 7.90 | 8.69 | 1.60 | 8.00 | 3.00 | 14.00 | 8.70 | SHORT | | ||
| TC060H098 | M6 | 9.80 | 8.69 | 1.60 | 8.00 | 3.00 | 14.00 | 10.8 | STANDARD | | ||
| TC060H120 | M6 | 12.0 | 8.69 | 1.60 | 8.00 | 3.00 | 14.00 | 13.2 | LONG | | ||
| TC080H095 | M8 | 9.50 | 11.06 | 1.96 | 10.1 | 3.80 | 17.70 | 10.5 | SHORT | | ||
| TC080H124 | M8 | 12.4 | 11.06 | 1.96 | 10.1 | 3.80 | 17.70 | 13.7 | STANDARD | | ||
| TC080H150 | M8 | 15.0 | 11.06 | 1.96 | 10.1 | 3.80 | 17.70 | 16.5 | LONG | | ||
| TC100H120 | M10 | 12.0 | 13.95 | 1.96 | 13.0 | 4.90 | 22.80 | 13.2 | SHORT | | ||
| TC100H160 | M10 | 16.0 | 13.95 | 1.96 | 13.0 | 4.90 | 22.80 | 17.6 | STANDARD | | ||
| TC100H180 | M10 | 18.0 | 13.95 | 1.96 | 13.0 | 4.90 | 22.80 | 19.8 | LONG | |
The TC Insert for plastic has two or more cutting flutes to maintain stability. Outward stress is reduced by the action of self tapping so that it may be used in brittle materials and also where there are thin walls. The balanced cutting load of the insert reduces 'side thrust' caused by predominately only one cutting edge and therefore guarantees much closer axial alignment of the insert in the hole. Also, because each cutting thread has less distance to travel between start and finish of the installation process (due to the coarse external thread), there is less chance of it breaking down in hard abrasive materials.
Request information about:
Series: 20105 Type: TC Screwin* Insert Short for Thermoplastic